Scaffolding & Site Access

H-frame (tubular frame) scaffold set is a light-to-medium-duty access scaffold system used for plastering, painting, tiling, and façade work on Malaysian construction sites. The system assembles welded steel H-frames, cross braces, base plates, and guardrails into load-bearing bays rated at ≥270 kg per bay. Frame OD is typically 38 mm or 48.3 mm; standard widths are 1.219 m (4 ft) or 1.524 m (5 ft) at 1.7 m or 2.0 m lift heights. Complies with MS 1462:2012 and BS EN 12811-1:2003. Must be erected by a DOSH-recognised competent person under BOWEC Regulations 1986. Sold per set inclusive of frames, braces, and base plates. HS 7308.40 · import duty 15% · SST 5%.

Ringlock scaffold standard (vertical post) is the load-bearing upright of a modular ringlock scaffold system, used for high-load multi-deck scaffolding on industrial plants, bridges, and multi-storey construction in Malaysia. The hot-dip galvanised steel tube (OD 48.3 mm × 3.2 mm wall) carries a welded rosette disk at every 500 mm interval, accepting ledgers, diagonal braces, and transoms from up to eight directions without loose fittings. Common lengths range from 0.5 m to 3.0 m. Complies with BS EN 12811-1:2003 and EN 39:2001. Sold per piece. HS 7308409000 · import duty 15% · SST 5%.

Ringlock scaffold ledger is the horizontal tube that spans between ringlock standard posts to define bay width and support scaffold board decking in modular ringlock systems used across Malaysian construction projects. Pressed-steel wedge-head end connectors slot into the rosette disk on the standard post and lock with a single hammer blow — no loose nuts or bolts. Common bay lengths range from 0.732 m to 3.0 m. Tube OD 48.3 mm, hot-dip galvanised or painted steel. Complies with BS EN 12811-1:2003. Sold per piece. HS 7308409000 · import duty 15% · SST 5%.

Ringlock scaffold diagonal brace is a steel tube connecting two adjacent ringlock standards along a scaffold face or through a bay to resist lateral racking forces and maintain structural stability. End plates engage the standard's rosette disk in fixed or swivel configuration. Tube OD is 42.4 mm or 48.3 mm; brace length is bay-matched (e.g., approximately 1.803 m for a 1.5 m × 1.0 m bay) and supplied in pairs per bay. Compliance with BS EN 12811-1:2003 stability requirements is mandatory for all regulated scaffolding in Malaysia under CIS 22:2021. Sold per piece. HS 7308409000 · import duty 15% · SST 5%.

Kwikstage modular scaffold system is a wedge-locking access scaffold used for residential mid-rise, commercial fit-out, and maintenance work in Malaysia, valued for faster erection than tube-and-coupler systems. Steel standards (OD 48.3 mm) feature pressed-steel triangular cup-and-lug nodes at 500 mm intervals; ledgers and braces hook in and are secured with a single hammer-blow wedge. Bay widths are typically 1.219 m or 1.829 m; lift heights 1.0 m or 2.0 m; standard-duty rating ≥675 kg per bay. Complies with BS EN 12811-1:2003 and AS/NZS 4576. Sold per set. HS 7308409000 · import duty 15% · SST 5%.

Aluminium mobile access tower is a self-contained, wheeled work platform used for indoor and outdoor maintenance, electrical, painting, and finishing work at heights up to approximately 12 m in Malaysia. The lightweight aluminium alloy frame (typically 6061-T6) reduces erection effort compared to steel scaffold. Tower widths range from 0.6 m to 0.85 m; supplied as a complete kit including frames, platforms, guardrails, and locking castors. Complies with BS EN 1004-1:2020 and BS EN 12811-1. Maximum platform load 225 kg/m². Must be stabilised with outriggers when height-to-base ratio exceeds 2:1. Sold per set. HS 7308409000 · import duty 15% · SST 5%.

Scaffold staircase tower is a modular temporary stair system providing safe pedestrian access to upper scaffold levels and construction floors on multi-storey Malaysian sites. Modular steel stringers and anti-slip treads assemble at 45° or 55° flight angles; bay widths range from 1.0 m to 1.5 m with landing platforms at each floor level. Handrail height is ≥1.0 m. Hot-dip galvanised or powder-coated steel construction; compatible with most ringlock and H-frame scaffold standards. Complies with BS EN 12811-1:2003. Mandatory under DOSH BOWEC Regulations 1986 for scaffolds with more than one working level. Sold per set (per floor level). HS 7308409000 · import duty 15% · SST 5%.

Adjustable base jack (screw jack with base plate) is fitted to the base of scaffold standards or formwork shores to level a scaffold structure on uneven ground in Malaysian construction. The threaded steel spindle (OD 38 mm or 48 mm) allows height adjustment up to approximately 500 mm; base plate is 150 × 150 mm or 180 × 180 mm. Safe working load is typically 30–50 kN per jack. Both U-head variants (for timber beams in formwork) and flat-plate variants are available. Hot-dip galvanised or painted finish. Complies with BS EN 74-3:2005. Sold per piece. HS 7308409000 · import duty 15% · SST 5%.

Scaffold coupler (clamp) is the connecting fitting used in tube-and-coupler scaffolding to join 48.3 mm steel tubes at fixed or variable angles on Malaysian construction sites. Right-angle (fixed) couplers connect perpendicular tubes at 90°; swivel couplers allow any angle for bracing and raker tubes; putlog couplers connect a horizontal tube to a board bearer. All are hot-dip galvanised drop-forged steel. Right-angle and swivel types comply with BS EN 74-1:2005; minimum slip resistance 6.1 kN per coupler. Also referenced under MS 1462:2012. Sold per piece. HS 7308409000 · import duty 15% · SST 5%.

Scaffold board (timber plank) is the working platform decking laid across scaffold ledgers and tube bearers to form the walking and working surface in tube-and-coupler and frame scaffold systems on Malaysian sites. Cut from softwood or tropical hardwood to BS 2482:2009, boards are 225 mm or 250 mm wide, 38 mm or 50 mm thick, in lengths from 1.5 m to 3.9 m. Hoop-iron end bands prevent splitting. Boards are inspected for cracks, notches, and excessive deflection before each use and reused multiple times before disposal. Sold per piece. HS 4407299900 · import duty 0% · SST 5%.

Scaffold caster wheel is a swivel-mount castor fitted to the base of mobile scaffold towers and aluminium access towers to allow repositioning across flat surfaces on Malaysian construction and maintenance sites. Each caster includes a positive-locking brake mechanism that holds the tower stationary during use. Cast iron or pressed steel wheel body with rubber or polyurethane tyre; stem OD sized to insert into standard scaffold tube ends (38 mm or 48.3 mm). Wheel diameter 150–200 mm; load capacity typically 150–250 kg per wheel. Required for any mobile scaffold tower operating under DOSH BOWEC Regulations 1986. Sold per piece or in sets of 4. HS 7326909900 · import duty 5% · SST 10%.

Scaffolding rental (per set per month) is a service covering the supply, erection, hire, and dismantling of a complete scaffold system for a defined period on Malaysian construction projects. The scaffold set is defined by an erection drawing (area in m² × lift height); minimum rental is typically one calendar month. Erection and dismantling must be carried out by DOSH-qualified scaffolders under CIS 22:2021. Scaffolds exceeding 15 m height require PE-signed design drawings under BOWEC Regulations 1986, Regulation 95. Service providers must be registered with CIDB. From 1 July 2025, scaffolding rental is indicatively subject to 8% Service Tax under Finance Act 2025 amendments.

Aluminium double-sided (A-frame) step ladder is a self-supporting portable access ladder that opens to form an inverted-V shape, allowing workers to climb and work from either side without leaning the ladder against a wall. Widely used on Malaysian construction sites and renovation projects for ceiling fixing, electrical installation, painting, and interior finishing. Aluminium alloy construction; anti-slip rubber feet and step treads. Available in 4- to 12-step sizes covering approximately 1.0 m to 3.2 m open working height. Load rating typically 100–150 kg per EN 131-1+2 or equivalent. Sold per unit.

Aluminium single-sided (lean-to) extension ladder is a non-self-supporting straight or telescopic ladder designed to lean against a wall or structure at the correct working angle for reaching heights on Malaysian construction sites and maintenance jobs. Used for roof eaves, upper slab edges, and external wall work. Aluminium alloy construction with anti-slip rubber feet; rung spacing typically 300 mm. Available in fixed and telescopic extension variants; common lengths range from 1.5 m to 6.0 m. Must be used at the safe angle (approximately 75° / 4:1 ratio) and secured at the top. Load rating per EN 131-1+2 or equivalent. Sold per unit.

Aluminium folding step platform is a compact, portable work platform used to access heights of 0.5–1.0 m on Malaysian construction sites, warehouses, and in maintenance work where a step-ladder would be excessive. Available in 2-tread (~700 mm platform height) and 3-tread (~1,000 mm) configurations. Aluminium alloy frame with non-slip tread surfaces and non-slip rubber feet; working load typically 150 kg. Folds flat for easy transport and on-site storage. Rated to EN 14183 (Steps for professional use). Lighter and more stable than step-stools; suited for interior fit-out, electrical work, and warehouse picking. Sold per unit.